Up for sale is our BRAND NEW SF-902 dyno with Soundmaster Test Cell. This is the EXPERT system with X-Console, integrated dyno engine starting system, heavy duty input shaft, 8 pressure transducers and 02 sensors, and several other upgrades. This setup was ordered new in 2008, and has been 99% setup, but NEVER USED. Everything is complete and either new in the box or installed without being used.
This could be a complete turnkey dyno shop business, all you need is the location or shop building to set it up in. Dyno sessions typically go for $500-$600 per session.
This setup was bought new for $114,103 (have all receipts). Price lowered to $69K. That's about 40% off the new price, and everything is still brand new in the box, never used.
The control table and console. Controls for the pumps and exhaust fan can be seen on the grey box on the right side of the table. Superflow supplied Dell computer control system can be seen under the table.
Close up of console. Everything is BRAND NEW.
Close up of the control box. The two switches are for the pumps, one for the supply and one for the return. The digital display is a speed controller for the exhaust fan. This allows you to run the fan at lower speeds while in the dyno room working on the engine, giving you a nice breeze which will take the heat off the engine without hurricane force winds that are typical with an "on/off" type of exhaust fan.
Inside view of control box showing relays, automation controls, etc.
Inside of test cell room.
Front of dyno showing control box, etc. All necessary links from the control console (throttle control, etc - as well as power) have all been nicely run through conduit and liquitite directly to the dyno frame.
Side of control box showing panels.
Another shot of dyno showing universal bellhousing and starter setup. The input shaft is the upgraded 2" heavy duty 10 spline version.
Close up of base showing fuel pump & system.
Close up of water lines in the exhaust plenum behind the dyno.
Looking up the plenum into exhaust fan. Fan is approx. 36" diameter.
Close up showing the SuperStart and universal bellhousing. This allows any engine to be started directly by the dyno. No having to stock different brand-specific models of starters, flywheels, etc.
Exterior view of the rear of the room showing the exhaust plenum where it exits the building. Total height is approx. 18 feet.
The return pump. All pumps are 5HP, three phase 208/240V. All motors are wired correctly with shut-offs at correct level. All electrical comes with the dyno.
Drive motor for main exhaust fan, looking into the plenum from access panel. Also 208/240V three phase.
Wide view of the room showing intake baffle (on the right) and exhaust baffle/ducting (on the left).
1635 gallon water tank is stored in a standard shipping container which is located next to the building. This is the super thick extra heavy duty polyethylene, which will stand up to years of repeated use and heating and cooling cycles.
Close up of supply pump near tank showing Y strainer.
Support brackets for water tank, and bag filter for return line. This is the only part of the plumbing that has not actually been installed yet.
Dyno Includes the following reciepts:
Superflow:
1200A-902XC-EXP SF902 XConsole EXPERT DYNO SYSTEM #393 $45,500
1200A-2161-4 Pressure transducer panel upgrade $400
SP-2 Fast O2 Sensors (AMP Conn) $650
SP-2 Tripp Lite Power Supply $120
1200A-5002 Superdrive W/ 2 inch 10 spline Shaft $1072.00
2400Z-0827-03 LG Chrysler Bell Housing Adapter $120
4500P-20080 2 inch Poly Y Strainer, 80 mesh $95
4000P-610076 Universal Bell Housing Adapter $1095
1200A-6030 SuperStarter $3995
Total of Above: $53,047
Freight $1000
Tax $4641
Superflow Total: $58,688
Soundmaster Test Cell: $31,194
Water tank, Heavy duty (extra thick) polyethylene, 1635 gallon, with straps: $2676
Pumps, filters, valves, etc (Grainger) $3899
Plumbing, Test cell and dyno assembly and setup: $5897
Misc. Plumbing pipe, valves, fittings, (all industrial SCH80) etc. $883
Electrical (includes wireing all pumps, relays, shutoffs, plugs and lights inside dyno room, etc) $4351
Speed control unit + control: $339+63=$402
Exhaust ducting and grills, etc $4013
Acid wash, primer and paint interior and exterior of cell $1800
Logo and stripes custom painting $300
Total Investment: $114,103
This setup was bought new for $114,103 (have all receipts). Price lowered to $69K. That's about 40% off the new price, and everything is still brand new in the box, never used. Sold as is, where is.
Buyer is responsible for disassembly and removal. We have a forklift and can offer some help loading.
For details call 661.951.3700