|
Power Steering This page includes everything related to power steering setups, including power steering pumps, pump pulleys, brackets, etc. |
| Shown above is our Saginaw power steering
pump. These are original factory parts that are fully remanufactured in the
USA, with all new seals, bearings, etc. Purchase is outright, there is no
core return required. These are for pre 1975 applications which use a locknut
and woodruff key to hold the pulley onto the pump. These are great for
factory replacement, or for adding power steering to a car which didn't have
it from the factory. Use this pump with our 132-1003 pulley, 127-1006
brackets, 109-1513 bolt kit and 138-1010 cap for a complete and ready to
bolt on unit.
Part No: 138-1007 - Power Steering Pump - Saginaw w/Key - Price: $89.95 |
| Shown above is our brand new power steering pulley for early style
(pre 1975) Saginaw Power Steering Pumps
which use a locknut to hold the pulley onto the pump. The steering pump for
these can be easily identified because it will have a woodruff key in the
shaft (similar to a crankshaft) and the end of the shaft will be threaded
for the locknut which secures the pulley. These are designed to
work with our 132-1002 reproduction water pump pulley and 132-1001 double
groove crank pulley for proper belt spacing and alignment. Forget about
scrounging up used and often damaged originals... we've got great quality
brand new reproductions at practically swap meet prices!
Part No: 132-1003 - Power Steering Pulley - Saginaw w/Key - New Reproduction. Price: $34.95 |
| Shown above is our brand new power steering pulley for
late style (1975 and later) Saginaw Power Steering Pumps
which use press fit to hold the pulley onto the pump. The steering pump for
these can be easily identified because the shaft will be smooth with no
woodruff key and no threads at the end. There is a tool available from most
places which sell specialty auto tools (Summit racing, Mac, Snap-on, etc)
which allows you to press these on and off by hand. These are designed to
work with our 132-1002 reproduction water pump pulley and 132-1001 double
groove crank pulley for proper belt spacing and alignment. Forget about
scrounging up used and often damaged originals... we've got great quality
brand new reproductions at practically swap meet prices!
Part No: 132-1004 - Power Steering Pulley - Saginaw Press Fit - New Reproduction. Price: $34.95 |
| Shown above is our brand new American
Made power steering bracket set for Saginaw Power Steering Pumps. These fit
all big block engines, all years, with all car-type water pump housings
(aluminum and iron.) We send
these through black powder coating for a great looking durable finish. Will
work with early or late style Saginaw power steering pumps. Will not work
with Federal Pumps. Part No: 127-1006 - Power Steering Pump Brackets - Saginaw Style - New Reproduction: $29.95 |
| Our power steering bolt kit includes
every bolt, nut and washer needed to attach our power steering brackets
(part #127-1006) to both the engine and the power steering pump. We even
include the impossible to find special locknut to secure the power steering
pulley to the pump, (for use on early style Saginaw pumps only) and the
special double ended studs which attach the rear bracket to the back of the
pump. And, we
supply all the hardware in a high strength & high grade version. Part No: 109-1513 - Bolt kit - Power Steering - New. Price: $14.95. |
| Shown above are our brand new
reproduction power steering caps. These are the plastic type for use with Saginaw pumps. The
originals were Chrysler part number 2891284.
They have a dipstick integrated into them
and say " Fill to proper level Do not overfill Use approved Fluid" on them.
These are light grey color.
Part No: 138-1010 - Power Steering Cap - New Reproduction - Saginaw Style: $12.95 |
| Shown above are our reconditioned
factory power steering caps. The metal type on the left is used with Federal
pumps (no longer available), and the plastic type on the right is used with Saginaw pumps. The plastic Saginaw caps are Chrysler part number 2891284.
They have a dipstick integrated into them
and say " Fill to proper level Do not overfill Use approved Fluid" on them.
Part No: 100-1117 - Power Steering Cap - USED FACTORY - Saginaw Style: $5.95 - CLEARANCE SPECIAL WHILE SUPPLIES LAST |
| We've also sourced the belts which
work perfectly with our reproduction alternator and power steering brackets
and pulleys. These quality belts are made by a division of Goodyear, (even
though they don't have the "Goodyear" logo printed on them..
Part #138-1001 V-belt fits around the crank, water pump and alternator on all non-air conditioning big block cars. It works with the triangular alternator brackets, bolt and spacer kits listed above, and our reproduction non-AC water pump pulley (listed on our WATER PUMP PULLEYS page) and our reproduction non-AC crank pulleys (listed on our CRANK PULLEYS page.) It is used on cars with AND without power steering. Part No: 138-1001 - V-Belt - Alternator & Water Pump drive - Non A/C - NEW - Price: $14.95 Part #138-1002 V-belt fits around the second groove of our 132-1001 reproduction double groove crank pulley and goes directly to the power steering pump only. It is used as a second belt on power steering cars. Works with the power steering pumps, pulleys, brackets and bolts listed on this page. Part No: 138-1002 - V-Belt - Power Steering drive - NEW - Price: $14.95 |
All website content copyright 440 Source
(661) 951-3700